Model No. WEBE06010
Serial No.
Write the serial number in the space
above for reference.
USER’S MANUAL
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are commit-
ted to providing complete customer
satisfaction. If you have questions,
or if there are missing parts, we will
guarantee complete satisfaction
through direct assistance from our
factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians
on our customer hot line will pro-
vide immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
CAUTION
Visit our website at
Read all precautions and instructions
in this manual before using this
equipment. Save this manual for
future reference.
new products, prizes,
fitness tips, and much more!
Before You Begin
Thank you for selecting the versatile WEIDER® ROCK &
TONE body toning system. The ROCK & TONE body ton-
ing system is designed to help you develop the muscle
groups of the lower body. Whether your goal is a shapely
figure, dramatic increase in muscle size and strength, or a
healthier cardiovascular system, the ROCK & TONE body
For your benefit, read this manual carefully before
using the WEIDER® ROCK & TONE body toning sys-
tem. If you have additional questions, please call our
Customer Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please mention
toning system will help you achieve the specific results you the product model number (WEBE06010) and the serial
want.
number found on a decal attached to the body toning sys-
tem (see the front cover of this manual).
Assembly
1. Press a 2” Round Outer Cap (15) onto each end of the Rear
Stabilizer (8) and the Front Stabilizer (9, not shown). Note:
The Rear Stabilizer is longer than the Front Stabilizer.
1
8
21
15
22
Attach the Rear Stabilizer (8) to the Base (2) with two M8 x
63mm Carriage Bolts (21) and two M8 Nylon Locknuts (22).
15
2
22
2. Attach the Front Stabilizer (9) to the Adjustment Frame (3)
with two M8 x 63mm Carriage Bolts (21) and two M8 Nylon
Locknuts (22).
2
28
6
2
35
3
23
22
Press the 30mm Square Inner Cap (36) into the Adjustment
Frame (3) and secure it with the M4 x 12mm Screw (35).
Insert the Adjustment Frame through the Slider Bushing (33)
and into the Base (2). Insert the Adjustment Pin (18) into the
indicated hole in the Base and through a hole in the
Adjustment Frame.
33
18
36
22
9
21
Attach the Press Plate (6) to the Adjustment Frame (3) with
two M8 x 43mm Carriage Bolts (28), two 5/16” Washers (23),
and two M8 Nylon Locknuts (22).
3
16
1
3. Make sure that the End Plate (11) is inside of the Angled
Cap (10). Press the Angled Cap onto the bottom of the
Backrest Frame (1). Press a 38mm Square Inner Cap (16)
into the top of the Backrest Frame.
22
23
Attach the Pivot Frame (7) to the Backrest Frame (1) with
two M8 x 52mm Button Bolts (29), two M8 Washers (23),
and two M8 Nylon Locknuts (22).
7
29
Attach the Pivot Frame (7) to the Base (2) with an M10 x
64mm Button Bolt (25) and an M10 Nylon Locknut (24). Do
not overtighten the Nylon Locknut; the Pivot Frame
must be able to pivot easily.
23
22
11
24
2
10
25
3
4. Slide a Grip (14) onto each end of the Handlebar (13).
4
20
Attach the Handlebar (13) to the Backrest Frame (1) with two
M8 x 52mm Button Bolts (29), two M8 Washers (23), and
two M8 Nylon Locknuts (22).
1
14
13
Attach the Small Seat (20) to the Handlebar (13) with two
M6 x 42mm Button Screws (34) and two M6 Washers (26).
23
29
26
34
14
22
23
5. Insert an M6 x 50mm Carriage Bolt (32) into the center hole
of the Support Plate (12). Attach the Support Plate to the
Backrest (4) with two M6 x 16mm Button Screws (27).
5
26
30
4
1
Attach the Backrest (4) to the the Backrest Frame (1) with
the M6 x 50mm Carriage Bolt (32), an M6 Washer (26), and
an M6 Nylon Locknut (31).
12
26
31
27
Secure the Backrest (4) with an M6 x 55mm Button Screw
(30) and an M6 Washer (26).
32
The use of the remaining parts will be explained below.
Adjusting The Body Toning System
This section explains how the body toning system can be adjusted. Inspect and tighten all parts each time you use the
body toning system. Replace any worn parts immediately. The body toning system can be cleaned with a damp cloth
and a mild, non-abrasive detergent. Do not use solvents.
Adjusting the Press Plate
To adjust the distance between the Small Seat (20) and the
Press Plate (6), remove the Adjustment Pin (18) from the Base
(2). Slide the Adjustment Frame (3) into or out of the Base until
the Press Plate is in the correct position. Insert the Adjustment
Pin into the indicated hole in the Base and a hole in the
Adjustment Frame. Note: For the correct starting positions,
refer to the Exercise Guide on page 5.
20
6
2
18
3
Adjusting the Resistance
To change the amount of resistance, remove the four Spring
Clips (5) from the indicated bars on the Base (2) and the Pivot
Frame (7). Slide the 25-lb. Bands (17) onto the bars and secure
the Bands with the four Spring Clips.
7
Bar
17
The 10-lb. Bands (not shown) can be attached in the same
manner. For maximum resistance, attach both sets of Bands .
Bar
5
WARNING:Always place an equal amount of
resistance on each side of the body toning system.
2
4
Exercise Guide
Leg Press
Calf Raise
One Leg Squat
One Leg Squat with Leg Extension
One Leg Side Squat
One Leg Side Squat with Leg Extension
5
Part Identification Chart
Refer to the drawings below to identify small parts used in assembly. The number in parentheses below each drawing is
the key number of the part from the Part List. Note: Some small parts may have been pre-attached for shipping pur-
poses. If a part is not in the parts bag, check to see if it has been pre-attached.
M10 Nylon
Locknut (24)
M8 Nylon
Locknut (22)
M6 Nylon
Locknut (31)
M4 x 12mm Screw (35)
M6 x 16mm Button Screw (27)
M6 x 42mm Button Screw (34)
M6 Washer (26)
M8 Washer (23)
R0501A
Part List—Model No. WEBE06010
Key No. Qty. Description
Key No. Qty. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1
1
1
1
4
1
1
1
1
1
1
1
1
2
4
1
2
1
2
Backrest Frame
Base
Adjustment Frame
Backrest
Spring Clip
Press Plate
Pivot Frame
Rear Stabilizer
Front Stabilizer
Angled Cap
End Plate
Support Plate
Handlebar
Grip
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
#
1
4
10
6
1
1
4
2
2
4
1
1
1
1
2
1
1
1
1
Small Seat
M8 x 63mm Carriage Bolt
M8 Nylon Locknut
M8 Washer
M10 Nylon Locknut
M10 x 64mm Button Bolt
M6 Washer
M6 x 16mm Button Screw
M8 x 43mm Carriage Bolt
M8 x 52mm Button Bolt
M6 x 55mm Button Screw
M6 Nylon Locknut
M6 x 50mm Carriage Bolt
Slider Bushing
M6 x 42mm Button Screw
M4 x 12mm Screw
30mm Square Inner Cap
User’s Manual
2” Round Outer Cap
38mm Square Inner Cap
25-lb. Band
Adjustment Pin
10-lb. Band
#
Exercise Video
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the
user’s manual for information about ordering replacement parts.
6
Exploded Drawing—Model No. WEBE06010
R0501A
16
30
4
26
12
27
5
32
26
1
31
22
23
20
7
19
17
14
29
29
22
22
15
21
23
13
22
24
29
6
11
10
26
14
34
22
8
2
25
15
28
33
35
3
18
23
22
36
22
22
15
15
9
21
7
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the fol-
lowing information when calling:
• The MODEL NUMBER of the product (WEBE06010)
• The NAME of the product (WEIDER® ROCK & TONE body toning system)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED DRAWING on
pages 6 and 7 of this manual).
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty
extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at
ICON's option, the product at one of its authorized service centers. All products for which warranty claim is made
must be received by ICON at one of its authorized service centers with all freight and other transportation charges
prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty
does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center, products used for com-
mercial or rental purposes, or products used as store display models. No other warranty beyond that specifically set
forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with
the use or performance of the product or damages with respect to any economic loss, loss of property, loss of rev-
enues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of what-
soever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages.
Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some
states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply
to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No.175062 R0501A
Printed in China © 2001 ICON Health & Fitness, Inc.
|