MIXED FUEL
COOKER
ZCG 611
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB
Contents
For the User
For the Installer
Important Safety Requirements
Instructions for the Installer
Installation
17
17
18
20
21
22
Important Safety Information
Description of the Cooker
Control Panel
2
3
4
Operation
5
Electrical connections
Commissioning
24 Hour Clock
6
Before the First Use of the Cooker
Using the Oven
9
Conversion from Natural to LPG Gas
9
Using the Gas oven
Gas Oven Cooking Chart
Grilling
10
11
12
13
13
15
15
15
16
Maintenance and Cleaning
Cleaning the Oven
Something Not Working
Service and Spare Parts
Customer Care
Guarantee Conditions
Description of the Cooker
Splash back
Semi-rapid burner
Auxiliary burner
Semi-Rapid burner
Rapid burner
Control panel
Shelf
Oven door
Storage drawer
3
Control Panel
2
1
GAS OVEN &
ELECTRIC GRILL
BACK LEFT
FRONT LEFT
FRONT RIGHT
BACK RIGHT
TIMER
GRILL
IGNITION
LIGHT
+
PUSH
BOTH
-
SET
TIME
STOP
9
4
8
3
5
7
6
Accessories
1. Grill function pilot light
2. Electric ignition push button
3. Oven Light push button
Grill/roasting pan
Grill trivet
4. Back left burner control knob (semi-rapid)
5. Front left burner control knob (rapid)
6. Front right burner control knob (auxiliary)
7. Back right burner control knob (semi-rapid)
8. Oven function control knob
9. 24 hour clock
Removable
handles
The Oven Cavity
Oven Light
Electric Grill
Fitting the Splash back
A stainless steel splash back is supplied with the
appliance. This is meant to be fitted on the rear edge of
the cooker's hob. The splash back package is in the
oven cavity.
1. Unpack the splash back and dispose of the packaging
with due regard to safety and the environment.
2. Slide the two bayonets of the splash back into the
relevant supports on the rear edge of the cooker's
hob.
FO 2653
4
Operation
Hob burners
To light a burner:
F
-
Push the electric ignition button which is marked with
a little spark ( ).
-
At the same time push in and turn the relevant control
knob anticlockwise to maximum position.
Then adjust the flame as required.
-
If the burner does not ignite, turn the control knob to
zero, and try again.
When switching on the mains, after installation or
a power cut, it is quite normal for the spark
generator to be activated automatically.
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
Burner
minimum
diameter
maximum
diameter
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
Large(rapid)
Medium(semi-rapid)
Small (Auxiliary)
180 mm.
120 mm.
80 mm.
260 mm.
220 mm.
160 mm.
Take care when frying food in hot oil or fat, as the
overheated splashes could easily ignite.
If you use a saucepan which is smaller than the
recommended size, the flame will spread beyond
the bottom of the pan, causing the handle to
overheat.
If the control knobs become difficult to turn, please
contact your local Service Force Centre.
Gas oven and Electric grill
Oven Function Control Knob
l
Oven switched off
l - max Range of temperature regulation for gas
140
oven
Grill - The heat comes only from the top
element
1 6 0
2 0 0
2 4 0
Grill function pilot light
The grill function pilot light will come on when the oven
function control knob is turned to
.
Oven light push button
This button will turn the oven light on.
5
24 Hour Clock
1. DECREASE CONTROL
2. INCREASE CONTROL
( )
( )
A
U
T
O
MINUTE MINDER SYMBOL ( )
PUSH
SET
TIME
PUSH BOTH CLOCK SETTING SYMBOL (
)
STOP
BOTH
CHILD SAFETY SYMBOL ( )
1
2
Setting the time of day
When the power supply is first switched on, or after a
powerfailure,0.00andAUTOwillflashalternativelyinthe
display.
A
U
T
O
To set the correct time of day:
PUSH
1. Press button “ ” and “ ” together (See Fig. 1).
2. Release buttons, then press button “ ”: 12.00 will
show in the display (See Fig. 2).
SET
TIME
STOP
BOTH
Fig. 1
3. Within 5 seconds press and hold either button “ ”
to increase or button “ ” to decrease the time until
the correct time of day on the 24 hour clock is reached.
To reset the correct time of day:
1. Press button “ ” and “ ” together. Then press and
hold either button “ ” to increase or button “ ” to
decrease the time until the correct time of day on the
24 hour clock is reached.
NOTE: The increase and decrease control buttons
operate slowly at first and then more rapidly. They
should be pressed separately.
PUSH
BOTH
SET
TIME
STOP
Fig. 2
Things to note
1. The time of day must be set before the oven will ope-
rate. There will be a few seconds delay before the
oven switches on.
6
Setting the minute minder
Theminuteminderalarmwillsoundattheendofatimed
period up to 23 hours and 59 minutes, but THE OVEN
WILL REMAIN ON, if it is in use.
To set the minute minder:
1. Press button “ ”: the display will read 0.00 and the
PUSH
BOTH
SET
TIME
Fig. 3
STOP
minute minder symbol ( ) will come on in the display
(See Fig. 3).
2. Release button “ ” , then press and hold button “ ”.
The display will count up in one minute intervals until
the interval to be timed is reached, e.g. 30 minutes
(See Fig. 4). The minute minder will begin to count
down once set and the display will revert to the time
of day.
3. At the end of the timed period, an acoustic alarm will
be heard and the minute minder symbol ( ) will flash
in the display (See fig. 5).
To switch off the acoustic alarm, press any button:
the minute minder symbol ( ) will go out.
To reset the minute minder:
PUSH
BOTH
SET
TIME
STOP
Fig. 4
1. Press button “ ”, then proceed as described above.
To cancel the minute minder:
1. Press and release button “ ”. Then press and hold
button “ ”: the display will count down in one minute
intervals to 0.00.
2. Release button “ ”. After a few seconds the display
will revert to the time of day and the minute minder
symbol ( ) will go out.
PUSH
BOTH
SET
TIME
STOP
Fig. 5
7
Child Safety Mode (only in
models with fully electric oven)
To avoid children switching on the oven, it is possible to
lock the oven controls. To lock the oven controls, the
oven must be switched off.
PUSH
BOTH
SET
TIME
A. To enter the Safety mode:
STOP
Fig. 6
1. Press buttons “ ” and “ ” at the same time and
keep them pressed until "ON" appears on the display
(see Fig. 6).
2. Release the buttons, then press button “ ”: "OF" and
the key symbol ( ) will show in the display (see Fig.
7). Release the button: after a few seconds the
display will revert to the time of day (see Fig. 8). The
oven is now locked (only in models with electric oven).
B. To exit from the Safety mode:
1. Press buttons “ ” and “ ” at the same time and
keep them pressed until "OF" appears on the display
(see Fig. 9).
PUSH
BOTH
SET
TIME
2. Release the buttons, then press button “ ”: the key
STOP
Fig. 7
symbol ( ) will go out and "ON" will show on the
display (see Fig. 10). Release the button: after a few
seconds the display will revert to the time of day.
The oven can now be operated.
IMPORTANT: if you enter the Safety mode accidentally,
please follow the instructions given in Step “B” (“To exit
from the Safety mode”).
Night dimming function
Between 22:00 (10pm) and 6:00 (6am) the figures and
symbols on the display will dim.
PUSH
BOTH
SET
TIME
STOP
Fig. 8
PUSH
BOTH
PUSH
SET
TIME
SET
TIME
STOP
STOP
BOTH
Fig. 10
Fig. 9
8
Before the First Use of the Cooker
Remove all packaging, both inside and outside
the cooker, before using it.
Before first use, the oven should be heated without food.
During this time, an unpleasant odour may be emitted.
This is quite normal.
1. Set the time of day with the "24 Hour Clock".
2. Ignite the gas oven burner and set the oven function
control knob to "max".
3. Open a window for ventilation.
4. Allow the oven to run empty for approximately 45
minutes.
This procedure should be repeated with the grill
function for approximately 5-10 minutes.
Do not clean the oven while it is still warm.
Using the Oven
Always cook with the oven door closed.
Stand clear when opening the drop down oven
door. Do not allow it to fall open - support the
door using the door handle, until it is fully
4
3
open.
The oven has four shelf levels, and is supplied with
two shelves.
The shelf positions are counted from the bottom
of the oven as shown in the diagram.
2
1
It is important that these shelves are correctly
positioned.
Do not place cookware directly on the oven
base.
Hints and Tips
Condensation and steam
When food is heated it produces steam in the same way
as a boiling kettle. The oven vents allow some of this
steam to escape. However, always stand back from
the oven when opening the oven door to allow any
build up of steam or heat to release.
•
Do not use baking trays larger than 30 cm x 35 cm (12
in x 14 in) as they will restrict the circulation of heat
and may affect performance.
If the steam comes into contact with a cool surface on
the outside of the oven, e.g. a trim, it will condense and
produce water droplets. This is quite normal and is not a
fault with the oven.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
Storage Drawer
Thestoragedrawerislocatedunderneaththeovencavity.
During cooking the storage drawer may become
hot if the oven is on high for a long period of time,
thereforeflammablematerialssuchasovengloves,
tea towels, plastic aprons etc. should not be
stored in the drawer.
Cookware
Ovenaccessoriessuchasbakingsheets,willalso
becomehot,thereforecareshouldbetakenwhen
removing these items from the drawer whilst the
oven is in use or still hot.
•
Use any oven proof cookware which will withstand
temperaturesof250°C.
•
Baking trays, oven dishes, etc. should not be placed
directly against the grid covering the fan at the back of
the oven, or placed on the oven base.
9
The effects of dishes
on cooking results
Dishes and tins vary in their thickness, conductivity,
colour, etc. which affects the way they transmit heat to
the food inside them.
A Aluminium, earthenware, oven glassware and bright
shiny utensils reduce cooking and base browning.
B Enamelled cast iron, anodized aluminium, aluminium
with non-stick interior and coloured exterior and dark,
heavy utensils increase cooking and base browning.
Using the Gas oven
Oven safety device
The cooker features a thermocouple; if for any reason
the flame should extinguish, the device will stop the gas
flow.
Before using your oven
Switch the oven to "max" and leave it to run empty
for about 45 minutes to remove any unpleasant
smell.
During cooking, the door should be opened as little
as possible to avoid heat loss, and excessive fuel
consumption.
To ignite the oven gas burner:
F
1. Open the oven door.
2. Push the electric ignition button which is marked with
a little spark ( ).
3. At the same time press the oven control knob and
turn it anti-clockwise until the maximum temperature
("max") is reached.
4. Firmly press the oven control knob for approximately
5 seconds, until the safety valve automatically keeps
the oven burner lit.
5. Release the control knob and then gently close the
oven door. To adjust the temperature, turn the knob to
the required setting after a few minutes.
If the oven burner accidentally goes out, turn
the oven knob to "l" and wait at least 1 mi-
nute before trying to light the burner again.
10
Gas Oven Cooking Chart
This chart is intended as a guide only. It may be necessary to increase or decrease the temperature to suit your
individual requirements. Only experience will enable you to determine the correct setting for your personal requirements.
SHELF
COOKING
TIME
TEMPERATURES
°C
FOOD
POSITION
PUDDINGS
Milk puddings
170
210
190
2
2
2
1½ - 2 hours
45-60 minutes
50-60 minutes
Baked sponge pudding
Baked custard
CAKES
Rich Fruit Cake
Christmas Cake
170
170
3
3
2¼ hours
3½ - 4½ hours
Victoria Sandwich
Madeira Cake
Small Cakes
Plate tart
210
210
225
240
240
225
210
2 or 3
20-30 minutes
1 hour
2 or 3
3
15-25 minutes
50 minutes
50 minutes
15-25 mins
25 minutes
2
2
Fruit pie
Mince pies
2 or 3
2
Profiteroles
YEAST MIXTURES
Bread
1lb Loaves
max
2 or 3
30-40 minutes
Bread
2lb Loaves
max
max
2 or 3
2 or 3
30-40 minutes
10-20 minutes
Rolls and Buns
ROASTING MEAT
Beef
225
225
225
225
210
225
225
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
20-30 minutes per lb / 1/2Kg
25-30 minutes per lb / 1/2Kg
30-35 minutes per lb / 1/2Kg
20 minutes per lb / 1/2Kg
15-25 minutes per lb / 1/2Kg
25 minutes per lb / 1/2Kg
25 minutes per lb / 1/2Kg
Lamb
Pork and veal
Chicken
Turkey
Duck and duckling
Stuffed poultry
11
Grilling
Grilling must be carried out with the oven door
closed. The grill pan handles must be removed
from the pan.
Cooking chart
Cooking time depends on the thickness of the meat and
not on its weight.
How to Use the Grill
1. Turn the oven control function knob to
The grill pilot light will come on.
2. Adjust the grid and grill pan runner position to allow
for different thicknesses of food. Position the food
close to the element for faster cooking and further
away for more gentle cooking.
F
Type of food
Mins per side
.
Baconrashers
Chicken joints
Gammonrashers
Lambchops
Pork chops
2 - 5
15 - 20
5 - 8
6 - 12
10 - 15
10 - 12
Sausages(turningasrequired)
Steaks(averagethickness)
Rare
3 - 6
Medium 6 - 10
Well done 8 - 12
1 - 11/2
Preheat the grill for a few minutes before sealing steaks
or toasting. Adjust the shelf level as necessary, during
cooking.
Toast
Hints and Tips
-
-
Most foods should be placed on the grid in the grill
pan to allow maximum circulation of air to lift the food
out of the fats and juices. Food such as fish, liver and
kidneys may be placed directly on the grill pan, if
preferred
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish lightly
with a little oil or melted butter to keep them moist
during cooking
-
-
-
Accompaniments such as tomatoes and mushrooms
may be placed underneath the grid when grilling meats
When toasting bread, we suggest that the top runner
position is used.
The food should be turned over during cooking, as
required.
O
L
I
12
Maintenance and Cleaning
Before any maintenance or cleaning can be carried out, you must DISCONNECT the cooker from the electricity
supply.
The Hob Top
The Burners
The hob is best cleaned whilst it is still warm, as spillage
can be removed more easily than if it is left to cool.
Regularly wipe over the hob top using a soft cloth well
wrungoutinwarmwatertowhichalittlewashingupliquid
has been added. Avoid the use of the following:
-householddetergentandbleaches;
Theburnercapsandcrownscanberemovedforcleaning.
Wash the burners caps and crowns using hot soapy
water,andremovemarkswithamildpastecleaner.Awell
moistenedsoapimpregnatedsteelwoolpadcanbeused
with caution, if the marks are particularly difficult to
remove.
-impregnatedpadsunsuitablefornon-sticksaucepans;
- steel wool pads;
After cleaning, be sure to wipe dry with a soft cloth.
- bath/sink stain removers.
A) Burner Cap
B) Burner Crown
C) Ignition Candle
Should the hob top become heavily soiled, it is
recommendedthatacleaningproductsuchasHobBrite
or Bar Keepers Friend is used.
The Pan Support
The pan support is dishwasher proof. If washing it by
hand,takecarewhendryingitastheenamellingprocess
occasionally leaves rough edges. If necessary, remove
stubborn stains using a paste cleaner.
Cleaning the Oven
The oven should be kept clean at all times. A build-up of fats or other foodstuffs could result in a fire, especially
in the grill pan.
Cleaning materials
Before using any cleaning materials on your oven, check
that they are suitable and that their use is recommended
by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives
should also be avoided.
External cleaning
Regularly wipe over the control panel, oven door and door
seal using a soft cloth well wrung out in warm water to
which a little washing up liquid has been added.
Clean the outer and inner door glass using warm soapy
water.Shouldtheinnerdoorglassbecomeheavilysoiled
it is recommended that a cleaning product such as Hob
Brite, or Bar Keepers Friend is used.
To prevent damaging or weakening the door glass
panels avoid the use of the following:
DO NOT clean the oven door while the glass panels
are warm. If this precaution is not observed the
glass panel may shatter.
•
Householddetergentandbleaches
•
Impregnatedpadsunsuitablefornon-stick
saucepans
If the door glass panel becomes chipped or has
deep scratches, the glass will be weakened and
must be replaced to prevent the possibility of the
panel shattering. Contact your local Service Force
Centre who will be pleased to advise further.
•
•
•
•
Brillo/Ajax pads or steel wool pads
Chemical oven pads or aerosols
Rustremovers
Bath/Sink stain removers
13
Oven Cavity
The enamelled oven cavity is best cleaned whilst the
oven is still warm.
Wipe the oven over with a soft cloth soaked in warm
soapy water after each use. From time to time it will be
necessary to do a more thorough cleaning, using a
proprietary oven cleaner.
Oven Shelves
To clean the oven shelves, soak in warm soapy water
and remove stubborn marks with a well wetted soap
impregnated pad. Rinse well and dry with a soft cloth.
Cleaning around the flame
spreader
- Remove the small flap.
F
- Slide forward the remainder of the lid.
- Lift from the back.
When cleaning around the flame spreader, particles can
fall into the drawer below.We recommend placing some
paper over the contents of the drawer whilst cleaning.
Please ensure the paper is removed after cleaning or it
may ignite.
We advise using a stiff dry brush to remove stubborn
grease deposits around the base of the unit (see Fig.).
Remove any remaining surface fat with a sponge while
the oven is still warm.
Place a brush or other suitable cleaning implement into
the aperture and brush around the base of the unit with a
suitable detergent.
FO 0177
UNDER NO CIRCUMSTANCES SHOULD THE
FLAME SPREADER BE REMOVED.
After cleaning, replace the lids correctly.
Replacing the Oven Light
Disconnect the appliance.
If the oven bulb needs replacing, it must comply with the
following specifications:
- Electric power: 15W,
- Electric rate: 230-240 V (50 Hz),
- Resistant to temperatures of 300°C,
- Connection type: E14.
These bulbs are available from your local Service Force
Centre.
To replace the faulty bulb:
F
1. Ensure the oven is disconnected from the electrical
supply.
2. Turn the glass cover anticlockwise.
3. Remove the faulty bulb and replace with the new one.
4. Refit the glass cover.
FO 0287
5. Reconnect to the electrical supply.
14
Something Not Working
If the appliance is not working correctly, please carry out the following checks, before contacting your local Service
Force Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,
a charge will be made even if the appliance is under guarantee.
SYMPTOM
SOLUTION
n There is no spark when lighting the gas
u Check that the unit is plugged in and the electrical
supply is switched on
u Check that the RCCB has not tripped (if fitted)
u Check the mains fuse has not blown
u Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
n The gas ring burns unevenly
u Check the main jet is not blocked and the burner
crown is clear of food particles.
u Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
u Check a cooking function / temperature have been
selected.
n
The oven does not come on
u Check the socket switch or the switch from the
mains supply to the oven is ON.
u Check the light bulb, and replace it if necessary
(see "Replacing the Oven light")
n The oven light does not come on
n The timer does not work
u Check the instructions for the timer.
u The temperature may need adjusting
n It takes too long to finish the dishes, or they are
cooked too fast.
n Steam and condensation settle on the food and the u Refer to the contents of this booklet, especially to
oven cavity.
the chapter “Using the Oven”.
u Leave dishes inside the oven no longer than 15-20
minutes after the cooking is completed.
Service and Spare Parts
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working.”
When you contact the Service Force Centre you will need
to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
5. The purchase date
Please note that a valid purchase receipt or
guarantee documentation is required for in-
guarantee service calls.
15
Customer Care Department
For general enquiries concerning your Zanussi appliance
or for further information on Zanussi products, please
contact our Customer Care Department by letter or
telephone at the address below or visit our website at
www.zanussi.co.uk
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
* calls to this number may be recorded for training purposes.
Guarantee Conditions
Zanussi guarantee conditions
*
Appliances found to be in use within a commercial
or similar environment, plus those which are the
subject to rental agreements.
Products of Zanussi manufacture which are not
marketed by Zanussi.
We, Zanussi, undertake that if, within 12 months of the
date of the purchase, this Zanussi appliance or any part
thereof is proved to be defective by any reason only of
faulty workmanship or materials, we will, at our option,
repair or replace the same FREE OFANY CHARGE for
labour, materials or carriage on condition that:
*
European Guarantee
*
*
*
The appliance has been correctly installed and used
only on the gas and electricity supply stated on the
rating plate.
The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any person
not authorised by us.
All service work under this guarantee must be
undertaken by a Zanussi Service Centre.
Any appliance or defective part replaced shall
become the Company's property.
If you should move to another country within Europe then
your guarantee moves with you to your new home
subject to the following qualifications:
*
The guarantee starts from the date you first
purchased your product.
*
The guarantee is for the same period and to the same
extent for labour and parts as exist in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be
transferred to another user.
Your new home is within the European Community
(EC) or European Free Trade Area.
The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
*
*
*
*
*
*
This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours, in which case a premium will be charged.
*
The product is installed taking into account
regulations in your new country.
Before you move, please contact your nearest Customer
Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after
you and your appliances.
Exclusions
This guarantee does not cover:
*
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside European Community (EC) or European Free
Trade Area.
France
Germany
Italy
Senlis
+33 (0) 3 44 62 29 29
+49 (0) 800 234 7378
+39 (0) 0434 39 4700
+46 (0) 8 672 53 90
+44 (0) 1753 219897
*
Nürnberg
Pordenone
Stockholm
Slough
Sweden
UK
16
Instructions for the Installer
Technical Data
Hob
Rear left burner (semi-rapid)
Front left burner (rapid)
2,000 W
3,000 W
2,000 W
1,000 W
Appliance Class 2 sub class 1 and Class 1
APPLIANCE CATEGORY
APPLIANCE GAS SUPPLY: Natural Gas G20 20mbar
:
II 2H3+
Rear right burner (semi-rapid)
Front right burner (auxiliary)
Dimensions
Oven
Height
900 mm
600 mm
600 mm
1.7 Cu. ft
Electric Grill
1,830 W
2,700 W
Depth
Gas Oven burner
Width
Oven light
15 W
Oven Capacity
TotalRating
1,845 W
Supply voltage (50 Hz)
230-240 V
BURNER
RAPID
(large)
SEMI-RAPID
(medium)
AUXILIARY
(small)
OVEN
TYPEOF
CHARACTERISTICS
GAS
POSITION
MAX
MIN
MAX
MIN
MAX
MIN
MAX
MIN
NOMINALTHERMAL
POWER (kW)
3.0
0.65
2.0
0.45
1.0
0.33
2.7
1.1
NATURAL
GAS
VALUE =
37.78 MJ/m3
NOMINALFLOW
RATE (m3/h)
20 mbar Ws - 50.7 MJ/ m3
0.286
119
0.057 0.190
Adjust. 96
0.038 0.095
0.028
0.257 0.105
114 Adjust.
NOZZLEREFERENCE
1/100 mm
Adjust.
70
Adjust.
NOMINALTHERMAL
POWER (kW)
2.8
0.65
2.0
0.45
1.0
0.33
2.7
1.1
LPG GAS
28-30/37
mbar
VALUE =
49.92 MJ/Kg
NOMINALFLOW
RATE (g/h)
202
86
43.5
40
144
71
29
32
72
50
21,5
28
195
83
79
55
NOZZLEREFERENCE
1/100 mm
Important Safety Requirements
The following requirements for ventilation must be met.
This appliance must be installed in accordance with the
Gas Safety (Installation and Use) Regulations (current
addition) and the I.E.E. Wiring Regulations. Detailed
recommendations are contained in the following British
Standard Codes of Practice - B.S. 6172, B.S. 5440: Part
2 and B.S. 6891: Current Editions.
The cooker should not be installed in a bed sitting room
with a volume of less than 20m3, if it is installed in a room
of volume less 5m3 an air vent of effective area of 110cm2
is required; if it is installed in a room of volume between
5m3 and 10m3, an air vent of effective area 50cm2 is
required, while if the volume exceeds 11m3 no air vent is
required. However, if the room has a door which opens
directly to the outside, no air vent is required even when
the volume is between 5m3 and 11m3.
Provision for Ventilation
The room containing the cooker should have an air
supply in accordance with B.S. 5440: Part 2: Current
Editions.
If there are other fuel burning appliances in the same
room, B.S. 5440: Part. 2: Current Editions should be
consulted to determine the requisite air vent
requirements.
17
Location of the appliance
Positioning the Cooker
This appliance must not be installed in a bed-sitting room
of volume less than 20m³or in a bathroom, shower room
or garage. It is essential that the appliance is positioned
as stated below (see fig.1) i.e. shelves, wall cabinets
and cooker hoods must be fitted a minimum of 787mm
directly above the top of the hotplate and 400mm above
the hotplate when fitted in line with the outside of the
appliance. If the units are intended to be fitted adjacent
to the appliance but less than 400mm above the hotplate,
then a minimum space of 100mm must be maintained
between the sides of the unit and the appliance (see fig.).
Curtains must not be fitted immediately behind the
appliance or within 150mm of the sides of the hotplate. If
fitted next to or between two base units a minimum space
of 1mm must be left between each unit and the side of
the appliance. The levelling feet fitted to the appliance
will achieve a nominal height to hotplate trims of 900mm
+20mm.
Caution:
Some soft or badly fitted floor coverings can be damaged
when the cooker is moved across their surface for
cleaning. It is advisable to ensure that the floor covering
in the area below the cooker is either securely fixed so
as not to ruck up when the cooker is moved or, if
preferred, removed.
L.P.G. cookers MUSTNOTbe installed below ground level,
i.e. in a basement, or aboard any boat, yacht or other
vessel.
Installation
1. Positioning the Appliance
(Fig. 1)
D
E
C
115
Note A: The appliance is designed to be flush fitted with
2mm clearance at each side to allow for it to be pulled
forward for cleaning etc.
B
Note B: The hotplate side trims should be flush with the
cabinets and must not be below. Adjustable levelling feet
at the front and rear are provided on the base of the
appliance. Adjustment is obtained by rotating in or out,
the feet at the front or rear of the appliance from the
underside of the appliance, with the drawer removed.
A spirit level should be placed on a cake tray on one of
the shelves to confirm that the appliance is correctly
levelled.
A
FO 1141
Fig. 1
The appliance must be installed in accordance to the
type X (standard EN 60335-2-6).
The levelling feet fitted to the appliance will achieve a
height to hotplate trims of 900mm-0 + 20mm.
Therefore the appliance can not be installed beside
furniture higher than the cooker worktop.
Note C: If the appliance is fitted next to a side wall or
cabinets above height of the hotplate trims, then a gap
of 115 mm is required.
Curtains must not be fitted immediately behind the
cooker or within 115 mm of the sides of the cooker.
This cooker must only be installed by qualified
personnel, according to the manufacturer’s instructions
and to the relevant British Standards.
Note D: Any wall cabinet or extractor must not be lower
than 780mm above hotplate level.
Note E: Wall cabinets may be fitted in line with the sides
of the base units, providing that the lower edge of the
wall cabinet is a minimum of 420mm above the worktop.
18
300 mm.
WALL FACE
BACK OF COOKER
ENGAGEMENT EDGE FOR
STABILITY BRACKET
LEVELLING FEET
BASE OF COOKER
A
PENCIL LINE ON THE FLOOR
295 mm.
SIDE VIEW
OF THE COOKER
PLAN VIEW OF THE COOKER
FO 0179
Fig. 2
Fitting the Stability Bracket
(Not supplied)
Connecting to Gas
This cooker is designed to be installed with an appliance
flexible connection. Connection is made to the RC 1/2
(1/2" B.S.P.) threaded entry pipe located just below the
hotplate level on the rear right-hand side of the cooker.
Check for gas soundness after connecting the gas
supply.
If the cooker has to be installed with a flexible supply
pipe, it is necessary that a stability device is fitted.
(See Safety Requirements: Page 22).
If a stability bracket is to be fitted by the installer, these
instructions should be read in conjunction with the leaflet
packed with the stability bracket.
The gas bayonet connector must be fitted in the shaded
area indicated in the diagram. Take into account that it
must be possible to pull the cooker forward sufficiently.
The hose must not get caught on the stability bracket.
Place the cooker in its intended position and level
cooker.
Note:
Mark off 295mm (11 1/2") from the right hand side of the
cooker as shown, this is the centre line of the bracket
fixing.
For certain types of gas bayonet connection used, it
may not be possible for the appliance to be pushed fully
back to the wall stops.
Draw a line 100mm (4") from the front edge of the
levelling feet (see Fig. 2) and remove cooker from its
position. Mark off 480mm (19") back from this line on
the centre line of the bracket to locate the front edge of
the lower bracket.
Important:
Flexible tubing MUST comply with BS.669 Current
Edition.
Fix lower bracket (with two fixing holes) to the floor, then
measure height from floor level to engagement edge on
back of cooker, dimension 'A' of Fig. 2.
Assemble upper bracket to lower bracket so that
underside of bracket is dimension 'A' +3mm (1/8") above
floor level. Re-position cooker and check that top
bracket engages into cooker back to a depth of 75mm
(3"), as shown in Fig. 2.
600
450
Should the stability bracket currently installed not allow
the cooker to stand correctly, ask the installer to replace
it with the correct type.
130
FO 0180
Fig. 3
19
Electrical connections
Any electrical work required to install this cooker
Permanent Connection
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
In the case of a permanent connection, it is necessary
that you install a double pole switch between the cooker
and the electricity supply (mains), with a minimum gap
of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the
current electric regulations.
THIS COOKER MUST BE EARTHED.
The manufacturer declines any liability should these
safety measures not be observed.
This cooker is designed to be connected to a 230-
240V 50Hz AC electrical supply.
The switch must not break the yellow and green earth
cable at any point.
Ensure that the cooker supply cord does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the cooker rating
plate. The rating plate is located on the oven frame.
The cooker is supplied with a 3 core flexible supply cord
incorporating a 13amp plug fitted. In the event of having
to change the fuse, a 13ampASTAapproved (BS 1362)
fuse must be used.
Should the plug need to be replaced for any reason, the
wires in the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue
Brown
- Neutral
- Live
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
F
1
the letter 'E' or the earth symbol
green and yellow.
or coloured
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal in
the plug which is marked with the letter 'L' or
coloured red.
NOTE: The earth wire should be about 2 cm. longer than
the live and neutral wires.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
FO 0390
Acut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard. Ensure that the
cut off plug is disposed of safely.
20
Commissioning
When the hob has been fully installed it will be necessary
to check the minimum flame setting. To do this, follow
the procedure below.
-
-
Turn the gas tap to the MAX position and ignite.
Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
a
Procedure:
F
-
-
-
Re-ignite the burner and set to MIN.
Remove the control knob.
The adjustment screw is located down the centre of
the gas tap control shaft or on the lower right hand
side of the shaft (see diagram).
To adjust, use a thin bladed screwdriver and turn the
adjustment screw until the flame is steady and does
not extinguish, when the knob is turned from MIN to
MAX. Repeat this procedure for all burners.
FO 1032
a) Minimum adjustment screw
b) Tap
-
Pressure Testing
F
-
Remove left hand pan support and front left burner
cap and crown.
-
-
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite another burner
supply.
-
-
The pressure reading should be nominally 20mbar
and must be between 17 mbar and 25mbar.
Turn off the burner supplies.
21
Conversion from Natural to LPG Gas
IMPORTANT
The replacement/conversion of the gas hob should
only be undertaken by a CORGI registered engineer.
It is important to note that this model is designed for use
with natural gas but can be converted for use with butane
or propane gas providing the correct injectors are fitted.
The gas rate is adjusted to suit.
Method
•
•
•
Ensure that the gas taps are in the 'OFF' position
Isolate the hob from the electricity supply
Remove all pan supports, burner caps, rings, crowns
and control knobs.
•
With the aid of a 7mm box spanner the burner injectors
can then be unscrewed and replaced by the
appropriate LPG injectors.
TO ADJUST THE GAS RATE
With the aid of a thin bladed screwdriver undo the by
pass screw about 1/4 of a turn (45°). Upon completion
stick the replacement rating plate near the gas supply
pipe.
Replacement of gas oven
burner nozzle
To replace the gas oven nozzle, follow this procedure:
a) remove the bottom of the oven;
b) undo screw 1 and take the oven burner out;
c) with a socket spanner 7 unscrew and remove the
nozzle, situated in the bottom of the oven, and replace
it with the proper one (seeTechnical data);
d) reassemble the burner following the same procedure
backwards.
FO 1072
Minimum level adjustment
of gas oven burner
After setting the oven on maximum temperature with door
closed for about 10 minutes, turn the knob on minimum.
To reach the thermostat by-pass screw and adjust the
minimum level, act as follows:
– take out the knobs;
– remove the front panel;
– in case of conversion from natural gas to LPG, tightly
screw the by-pass screw of thermostat (see fig.);
– to convert from LPG to natural gas, unscrew the by-
pass screw, until a regular small flame is reached.
– finally check that turning quickly the tap from
maximum position to minimum position, the flame
does not go out;
– reassemble the front panel and the knobs.
The oven burner does not need any primary air regulation.
22
CUSTOMER CARE
Zanussi
55-77 High Street
Slough
Berkshire, SL1 1DZ
Tel: 08705 727727
© Electrolux HouseholdAppliances Limited 2002
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and
lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
35677-2001
|